塑化廠集中供料系統
塑化廠集中供料系統可以使原料及粉塵對注塑生產的污染減至*底的程度，從而可以保持潔凈的生產車間，而塑化廠集中供料系統統獨特集中粉塵回收系統，清理更便捷、環保效果更是達到10萬級無塵室作業要求標準，并降低噪音，*終可實現無人化的自動化生產車間，樹立起現代化工廠管理的形象。

塑化廠集中供料系統安裝流程：

1、管道安裝時注意注塑機分管對位，不對位影響美觀。

2、管道下料段與中央供料杯連接長度約3-4米。

3、管道嚴禁有漏氣現象。

4、鋼管在連接時確保管夾正中心對接。

5、集中供料系統走管道，盡量減少?gòu)澋馈?br>
6、觀察廠房墻體結構，判定承受管路重量。

7、管道在條件允許控制高大約3米，方便于安裝后續保養。

8、裝支架注意天車、天花板、柱子。

9、原料房與系統控制擺放規劃。

10、管道排走方式。

11、機臺準確擺放位置的尺寸。

塑化廠集中供料系統采用微機集中自動控制，實現了對粒料的24小時連續供料作業。。根據不同成型機的生產量，靈活變更供料量。多臺小型微機分別控制各臺成型機的著色工藝，計量準確、混合均勻，并可靈活改變顏色，適應對產品的多顏色多品種要求。

Plastic Plant Concentrated Feeding System
The centralized feeding system of the plasticizing plant can reduce the pollution of the raw materials and dust to the bottom of the injection molding process, so that the clean production workshop can be maintained, and the centralized feeding system of the plasticizing plant concentrates the dust collection system, , Environmental protection effect is to reach 100,000 clean room operating requirements standards, and reduce noise, and ultimately can achieve unmanned automated production workshop, and establish a modern factory management image.

Plastic plant centralized feeding system installation process:

1, pipeline installation Note injection molding machine in charge, not the impact of beautiful appearance.

2, the pipeline under the material and the central feeding cup to connect the length of about 3-4 meters.

3, the pipeline is strictly prohibited leak phenomenon.

4, the pipe in the connection to ensure that the center of the tube folder docking.

5, centralized feeding system to take the pipeline, to minimize the corners.

6, observe the plant wall structure, to determine the weight of the pipeline.

7, the pipeline in the conditions allowed to control about 3 meters high, easy to install follow-up maintenance.

8, loaded bracket Note crane, ceiling, pillars.

9, raw materials and system control placed planning.

10, pipe discharge way.

11, the size of the machine accurately placed position.

Plastic plant centralized feeding system using computer centralized automatic control, to achieve the pellet 24 hours continuous feeding operations. The According to the production of different molding machine, the flexibility to change the amount of feed. More than a small computer to control the molding machine of each molding process, accurate measurement, mixed evenly, and flexible to change the color, to adapt to the product of multi-color and more variety requirements